Please know there will be a delay in despatching this product: This item is currently on Pre-Order - (Expected Arrival: Mid December)

NCR Nicotine Reinforcer RDA

Please know there will be a delay in despatching this product: This item is currently on Pre-Order - (Expected Arrival: Mid December)
Pre-Order NCR Nicotine Reinforcer Coil-Less RDA

Buy NCR Nicotine Reinforcer RDA | (RDA) Rebuildable Drip Tanks

Are you tired of the wires, coils and time-consuming building? Then the NCR New Concept RDA is right here for you! It features a food-grade PC outer cover with venting holes, providing a safe vaping experience. The 600,000 times cycle-uses a WAFER heater that holds up the resistance of 0.4-0.5ohm and is capable of self-cleaning within a short-time dry burning in 30-40W. This pack also comes with a heat-isolation gasket. Available in White. 
NCR Nicotine Reinforcer RDA

Parameters

Size: 24(D) x 40mm (H) (with 510 thread)
WAFER Material: SST aluminum nitride
WAFER Heater Resistance: 0.4-0.5ohm
Thread: 510 thread
Color: White

NCR Nicotine Reinforcer RDA

Coil-free Design, No Wire Building
600,000 Times Cycle-use WAFER Heater(0.4-0.5ohm resistance)
Visible Outer Cover with Venting Holes
Strengthened Nicotine Effect
Easy self-cleaning

NCR Nicotine Reinforcer RDA

It comes with

  • 1x NCR New Concept RDA
  • 1x Tool Pack

NCR Nicotine Reinforcer RDA

Installation and preparations: Put the Wafer Heater into the deck slot and screw it with the Allen wrench. Check the resistance by connecting it with a MOD.(Wafer heater is usually pre-installed ex-work. Due to the different feature of various mods, resistance may range from 0.4-0.5ohm accordingly.)

How to fold the cottons: Pre-cut Organic cotton is strongly recommended. Cut each piece of cotton into a strip with the size of 8mm(width)* 40mm(length). Fold the cotton strips from middle and cover the wafer heater from the top and insert the cotton ends into the deck.

How to fix the cotton holder: Put on the aluminum cotton holder to fix the cotton strips. Make sure the cotton strips are fixed properly for E-juice soaking and vaporization. Moisten the new cotton with E-juice from all the openings on the top, bottom and all 4 sides of the cotton holder.

Output modes selection: The MOD with AOC Power mode(Adjustable Output Curve)or Boosting mode is strongly recommended. To optimize the wafer heating function, please set up a considerably high wattage(70W-80W)at the initial firing stage for around 0.5-1 second, then drop the wattage to a relatively low level(40W-50W) to last for another 2-3 seconds. Users may customize the Power mode settings to personal preference. 

Clean the dirt and stains on the Wafer Heater: After being used for some time, you need to clean the Wafer Heater. Remove the cotton holder and give the Wafer Heater a dry burn at 30W-40W in 3 seconds. A fine grade sand paper can also be used to rubbed off the stubborn stains on the Wafer Heater. For regular maintenance you may use a toothbrush to clean the RDA deck and all connections with household detergents.

Write a review

Note: HTML is not translated!
    Bad           Good

  • Views: 3556
  • Product Code: V1562 - NCR Nicotine Reinforcer RDA
  • Availability: Pre-Order
  • £34.99

Available Options

Tags: Nicotine, Reinforcer, (RDA) Rebuildable Drip Tanks, tanks, drip, rebuildable, reinforcer, nicotine